The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you need. For work with with 5/8” shaft sizes. Includes set screws. Extra Features: Made of Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and 
equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, ideally lowering on hand requirements and allowing for alterations in shaft size if necessary. The barrel of the split tapered bushing is definitely split in two locations and is certainly keyed to the shaft. The barrel OD can be keyed to the drive component as well. The good thing about the split tapered bushing could it be will hold, regardless if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.
Taper bushing are widely used together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made from high quality engineered products with wonderful tolerance. The characteristic is easy to use and needs no added alteration. These bushings can fit almost all sorts of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations put bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full selection of both metric and imperial readily available.
Standard range fits up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete short reach range offered, for compact light-weight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for toughness and strength. U1 bushings are being used in an extensively broad range of applications, which include; sprockets, shaves, pulleys, gears, plus much more, we likewise offer all of these goods. What units this bushing apart is the high-quality steel engineering along with specific manufacturing and high quality control; this means that you always get yourself a premium quality regular product. What really sets us in addition to the other folks is our experienced expert workers and our company-wide goal of customer satisfaction.
1. Be sure the tapered cone areas of the bushing and the inside of the driven item are clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or different part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding suit on shaft.
4. With key on shaft, slide the sprocket or other portion type to the desired position on the shaft. Be sure to leave the heads of the cap screws available.
5. Align the sprocket or component type, tighten the screws additionally and progressively until they happen to be pulled up tight. Do not make use of extensions on the wrench handles and don’t allow the sprocket or component to be drawn i connection with flange of bushing. At this point there should be a gap between your bushing flange and sprocket, make certain this gap will not close.
Double split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for positive drive and increased torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to keep concentric bores
Available in in ., metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys on both the shaft and merchandise to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Personal locking taper provides the highest degree of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For work with with 5/8” shaft sizes. Comes with set screws. Further Features: Manufactured from Steel For use with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, ideally lowering on hand requirements and allowing for adjustments in shaft size if important. The barrel of the split tapered bushing is split in two areas and is certainly keyed to the shaft. The barrel OD can be keyed to the travel component Split Taper Bushing china aswell. The advantage of the split tapered bushing could it be will hold, regardless if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.